Spring Pistol Buyer's Guide

3r^d Edition, 4/15/2002
Shane "Supergeek" Lin
Super_geek@attbi.com

Springer Retreat
http://springer.airsoftretreat.com

The spring pistol is the simplest of all airsoft weaponry, requiring a manual cycling of the mechanism before each shot. The spring pistol functions by the slide carrying the piston, holding a spring against the frame of the pistol, to a catch, which holds it in that compressed position. On the way back to the original position, the slide also pushes a BB from the top of the magazine through an incline and into an O-ring, which holds the BB in place in the barrel. Upon pulling the trigger, the catch that holds the piston is released, sending it forth, against the piston shroud and forcing air from the shroud into a hole leading into the barrel. The resulting sudden increase in air pressure between the BB and the piston causes the BB to accelerate down the barrel of the gun. Some pistols are equipped with the Hop-Up system, which puts a backwards spin onto the BB as it sails through the air. This motion causes the air at the lower end of the BB to have a lower pressure than the air traveling at the upper end of the BB, and thus through the Bernoulli principle, generates lift. Guns with the Hop-Up system will have a much higher effective range as the forces of drag and gravity will affect the BB to drop in angle much later, thus providing a much straighter shot. Many of these spring pistols (including many High Grade Hop-Up Mauri pistols and their subsequent UHC copies) can be field striped. This process involves removing the slide from the grip and frame of the pistol, so that the pistol and barrel can be removed and cleaned or lubricated. Spring pistols that have the Hop-Up system will have what is known as fixed Hop-Up, in which the Hop-Up is pre-calibrated for a certain weight BB. Most pistols have this calibrated for .12g BBs, with Mauri HG Hop-Up pistols for .25g and newer KWC spring pistols for .2g and .25g. However, any type of 6mm BB, regardless of weight can all used, to varying degrees of success, in all types of spring pistols. In addition to the large amount of automatic pistol replicas, there are also small number of revolver replicas, which work by the spring in the grip being compressed by a hammer. Upon trigger pull, the spring is released and air is forced through a tube into one of the chambers, where it forces the BB into the barrel.

To understand the different aspects that make up a "good" spring pistol, first you must understand the factors that determine its effectiveness. These are the muzzle velocity (measured in FPS), the presence or absence of the Hop-Up system, and the quality of the materials and design for the internals and barrel (determined by manufacturer). Most of these can be determined by simply looking at different manufacturers, since the guns of the same company are pretty much on level with each other. Thus, a look at the major manufacturers of spring pistols follows:

Tokyo Marui (TM): This most well known manufacturer of AEGs offers a wide selection of spring pistols. These can be classified into three groups, literally “the Good, the Bad, and the Ugly.” The “ugly pistols are the oldest TM designs, with the BBs in a stick which is inserted into the base of the grip. These guns thus have no magazine, limited functionality, and no Hop-Up. The "bad" Mauri pistols are the older "High-Grade non-Hop-Up" models. Aside from the obvious fact that these guns do not possess the hop-up system, many of them have internal and external technical problems that cause them to wear down and break easily. On the other side of the spectrum, the newer "High-grade hop-up" Mauri pistols are considered by many as the best on the market as well as the industry standard. These pistols have a fixed hop-up system calibrated for .25g BBs, offering more range than those calibrated for .12g BBs. The quality of the plastic used to make Mauri guns is noticeably better than those of Mauri's Hong Kong (HK) counterparts and TM guns have the reputation of being reliable and long lasting as well as effective. Unless I am mistaken, all of the better TM pistols include trademarks, which are legally covered by putty or tape. All TM guns are considered Light Weight (LW) as they weigh around 300-350 grams, about a quarter of the actual real steel version. In short, these are the best guns to get if you can get your hands on them, which may be a problem. There are very few US retailers online that carry TM springers, so online auction sites like Ebay may turn out to be your best bet. The other alternative is to purchase them from Asian-based online retailers like RedWolf Airsoft, Wargamer's Club, and DEN Trinity to name a few. The problem with this is that shipping across the vast expanse of the pacific ocean is costly and at the fastest shipping rate (SpeedPost, which takes 5-7 business days), a TM springer will cost $15-$25 to ship and runs the risk of being seized by US Customs. The final problem is price: TM pistols are the most expensive in the industry, and while the $40-$50 price tag may pale relative to an upgrade AEG, it is still at least twice as much as a UHC copy. For extra magazines, it may be more desirable to buy UHC magazines for guns of the same model, since the UHC pistols, and hence the magazines, are copied from the TM design. Thus, the magazines will work when swapped around. Bottom line: excellent choice for serious airsoft players looking to play skirmishes frequently, but bad for the occasional weekend warrior just looking to shoot at targets in the back yard most of the time.

Tokyo Marui's Web Site is at: http://www.tokyo-marui.co.jp/

Specific model analysis:

H&K Mk.23 SOCOM : This is perhaps one of the best spring pistols on the market. Its large size is justified by its performance: it seems to hit farther than other HG HU TM pistols. It is also the first and as of now, only TM pistol to have a threaded barrel, able to mount the 16mm threaded accesories as the KSC GBB and real steel Mk.23s. However, like all previous HG HU pistols, most of the operating controls are molded-on, and of course features like the decocker are not functional. However, it is still a very impressive peice, extremely functional and quite pleasing to the eye. It is such a good blend of these qualities that many state-side retailers have began to sell these guns, for rather reasonable prices as well. For some very nice pictures, check out the gallery in the Articles section of the Springer Retreat, at http://springer.airsoftretreat.com.

Additional Note: The latest Tokyo Marui models released, the Mk.23 SOCOM and the new HG HU Colt M1911, seem to be better and more powerfully designed and were only released in High Grade models. This could signify a move towards higher quality designs.

UHC: Unicorn Hobbies Company of Taiwan is an interesting company. Most of their spring pistol designs are copied off of Mauri designs and made with cheaper materials with less stringent quality control (leading to the chance of a newly purchased gun being a “lemon,” although I myself have not encountered one in the dozen UHC guns that my team has bought). All of their guns include the hop-up system, calibrated for .12g BBs, which are less stable in wind than .2g BBs. A few of their models are also available in Light Weight and Heavy Weight (HW) models. The difference is that HW pistols are typically weighted down and are made of better looking and more durable materials. These changes push the weight from 300-350 grams to around 600-650 grams, depending on the model. These feel much more realistic in your hands, and can aid targeting. Accuracy for both LW and HW UHC guns are similar. While reportedly of slightly worse accuracy (in fair conditions - wind makes a big difference on accuracy as TM guns typically use .2g or .25g BBs as opposed to UHC's .12g BBs) than TM guns, UHC pistols do still have good reputations in the areas of reliability and service life. Although calibrated for .12g BBs, the hop-up unit on UHC guns can be used, with some success, to fire .2g BBs. This is from the author's personally experience, so maybe I was just lucky with my Beretta. Typically, the material quality of LW guns suffers while HW guns like the Beretta have a very nice matte black slide resembling the texture of the real article. There are no trademarks on UHC guns, although usually they tend to make clever parody logos that resemble the real ones. The magazine designs of both TM and UHC are identically. In a way, this is bad, because each BB must be individually loaded into the magazine, not like other designs were you could simply pour them in with a squeeze bottle. One bad aspect of UHC magazines is that when loaded with a few BBs and when pressure is applied to the upper side of the top BB, the entire magazine load of BBs flies out. This does not occur in TM pistols, even though the magazine design is the same, allowing the use of UHC magazines in TM pistols of the same model (and vice versa). When buying a UHC pistol, it is likely that UHC BBs will also be offered. While they are typically deformed and almost unusable in AEGs and gas guns, they will work quite well with springers, due to low price of spring pistols and the inherent tolerance of bad BBs by spring pistols. UHC pistols, unlike Mauri, are widely abundant in the US. They are imported mainly by two distributors: Leapers and Viper USA, which in turn ships them wholesale to retailers. LW pistols may be acquired for a mere $17 at www.tapco.com and HW models can be found in almost every major online airsoft-specific retailer (www.airsoftatlanta.com to name one) for $25 or so. Extra magazines are also offered at relatively low prices ($5). Bottom line: while not as well made, effective, reliable, long-lasting, or good-looking as Mauri guns, you can get two or even three UHCs for the price of a TM, and those two or three will last longer than the one Mauri. Good for plinkers and those just getting into airsoft.

UHC's web site is at: http://www.toygunuhc.com.tw/

Specific model analysis:

Beretta 92: This is perhaps one of the best low-priced spring pistols widely available in the US. It features an open ejection port, well-made sights, comparatively ergonomic grip, protruding barrel (useful for attaching suppressors), double action trigger pull, very easy and realistic field stripping, and a lanyard attachment. The HW version of this gun also includes a very nicely textured slide of matte black (unlike the shiny LW one). Finally, the slide lock (which acts as a safety on this gun, can be altered so that it is once more a slide lock.

Glock 17: The G17 is not a good choice for several reasons, the least of which is that I am a Beretta aficionado and think that Glocks look like undeveloped USPs. First, the ejection port does not open. This leads to situations in which a BB is left stuck in the slide area without a means of removal. Which brings me to the next problem: they cannot be field stripped and forced disassembly is reported difficult. While they do have decent accuracy, a pretty cool working trigger safety, and a relatively smooth slide pull, the Glock really cannot measure up to the Beretta in terms of ease-of-use.

USP: The USP is quite simply, woefully underpowered. On many examples of this gun, the length of the slide is a bit too long for the spring to be completely compressed, leading to very low FPS and thus range. This phenomenon occurs in sufficient frequency so that the applicable examples cannot be dismissed as a mere "lemons." Fortunately however, the FPS problem can reported be fixed by adding a spacer to the end of the spring. It also does have an open ejection port and a rather unsightly open space under the barrel through which you can see a weight. But, on the bright side, it can be rather easily field stripped.

KWC - Kien Well Co. of Taiwan offers some very nice pistols indeed. The guns are generally divided into two camps. Of the first, the exterior materials are superior to those used by UHC and there is a relatively large abundance of metal parts. The guns are of good quality and durability. The catch is that those guns do not shoot as accurately and do not have the Hop-Up system, killing the range at about 35 ft. The thing that's really devious is that many of these KWC guns have the hop-up logo very prominently displayed on the box, but most of them do not have it in reality. From my experience, these also have a bad tendency to break in ways so that the gun is unfixable without disassembly of the gun (which is a bit tricky to figure out). Acquiring these is done through major airsoft sites (like AirsoftAtlanta) for about the same price as UHC guns. The second camp of KWC guns are almost exactly the opposite. They are made of cheaper materials, are not very durable, have almost no metal parts, and seem to be easily broken, yet have exordinary performance for their price, with the help of .2g hop-up. The models of the KWC 1911 line follows the first camp (although reportedly, some of the newer models really do have hop-up), and the KWC "K"99 follows the second camp. Bottom line: The first type are good collector's items, for display purposes, but a less-than-great field weapon, while the second type are hardly ones to show off, but do offer very, very good performance.

KWC's web site is at: http://www.kwc.com.tw/

Additional note: Newer model KWC guns, such as the P99. do have Hop-Up actually and are rather nice, especially as the Hop-Up is tuned to .20g BBs.

Specific model analysis:

K99 (KWC’s non-trademarked name for the P99): This is one of the newer KWC guns and it is very nice! In fact, it could compete with the UHC Beretta HW. While KWC does regrettably leave its tradition of numerous metal parts (like in their 1911 series), this gun does have many nice features. Among these is the .2g calibrated Hop-Up, the exposed (but not open barrel) ejection port area, the slide lock, the quick-load magazine (which annoyingly drops the top BB after being ejected), and top-notch slide charging action. The Hop-Up unit is covered with a thin layer of oil though, so out of the box, it shoots like a wounded llama, but after 100 rounds, it starts shooting VERY well.

Colt 1911 10mm Custom: One of the 1911 series of KWC guns, this is a pretty old design. It has plenty of metal parts, a working grip safety, pretty high quality plastic body, slide lock, and a quick-fill magazine design, but lacks Hop-Up. But generally, this is a very decent collector’s gun.

Desert Eagle .50AE: The melding of the two worlds, taking the best from either. This has been called by many as the best spring pistols ever made, and for good reason too: it's built like a GBB, with metal operating controls and a sturdy frame. It's quite good looking, with a full half-inch barrel diameter that tapers off into the 6mm inner barrel, unlike the Marui and UHC versions. Finally, and most importantly, it's got adjustable hop-up, that almost inconcievable luxury, unheard of in the world of springer airsoft. This allows it very good range with an assortment of BBs. This is certainly quite the formidable gun.

HFC - Ho Feng Co. of Taiwan makes airsoft replicas of many of the more popular guns. Generally, they offer higher FPS than UHC pistols, but most models do not have hop-up. The materials, balancing, and design are also superior in some ways to UHC and Mauri pistols. For example, the sights on the HFC USP include a useful, if not simple, white dot for easy aiming. The UHC USP does not have this. Also, HFC does make the only HW USP on the market, and an excellent one at that as well. HFC guns may be purchased through most airsoft-specific online stores, but extra magazines for them are rather rare. Prices are similar to those of UHC HW pistols. Bottom line: good quality, good design, good looks, but since most guns do not have hop-up, range suffer too much to bear. The range difference is going to make you wish you'd have gotten a UHC in the long run unless you very desperately want a really good looking heavy USP.

Additional Note: Newer HFC models now sport .12g-calibrated hop-up, although the models that do tend to be very limited and usually not widely available in the US. Inquire about it to a retailer before purchasing.

Specific model analysis:

USP/P8: This is pretty much the best USP made in terms of functionality, design, and weight. It is heavy weight, has an open ejection port, quick-fill magazine design, numerous metal parts, slide lock, very realistic safety, ambidextrous magazine eject lever, and nice color and textures. BUT, it doesn’t have Hop-Up, which pretty much limits effective range to about 30,40 feet. Finally, this gun is a bit badly-designed. The piston is connected to the slide at one point, which places enormous pressure on one thin section of the slide, right behind the ejection port. So, after a length of time of constant use, this part breaks, disabling the gun.

Daisy - The famous American BB gun maker has gone back into the ring with their "Airstrike" pistol which, although reportedly really made by HFC, are at least readily available to the public through sports retailers and Walmart. while this obviously has the potential to cause harm to Airsoft's acceptance by the masses, it does provide the opportinity for the sport to grow. The "airstrike" pistol istelf is not much of a gun. It is based on a nickel-plated Beretta M92. The finish itself is not bad, but the large amounts of texts and warnings engraved on the slide itself is quite ugly. While there are plenty of metal parts for the operating controls, there is no hop-up, and accuracy and range are miserable. Overall, even with the avaialbility of this gun, it cannot be easily recommended.

Y&P - Generally regarded as a low quality manufacturer, Y&P does make some models that are rare among other manufacturers, including the Walther P99 springer (better to buy the KWC version though). The general consensus on this manufacturer is that while the gun looks somewhat good, it shoots terribly and will easily break after repeated use. Bottom line: to be avoided, since you can just get a good UHC gun for about the same price. Y&P guns are imported in the United States primarily by Spring-Time International (or STTI).

There are several Korean spring pistol manufacturers, but because of the general consensus being that the hierarchy of gun quality goes from Japan to Taiwan to Korea (and other countries), Korean regulations on gun FPS, and the relative scarcity of these pistols sold by US retailers, these cannot be seen as a serious consideration for pistol buyers, unless for display or collection purposes. Other than those, there is the French firm of 3PSA, which produces liscensed copies of the Marui guns for sale in Europe and the United States.

Acknowledgments: Thanks particularly to Inferno, who has provided many details about Tokyo Mauri and KWC 1911-series spring pistols through the airsoft forums as well as influence in gun modifications. Also, thanks to everyone that commented on my mistakes or offered me praise and criticism.


		Springer Retreat :: ReviewsSpring Pistol Buyer's Guide
News Reviews Buyer's Guide SPR Recommends Articles Workshop Gallery Video Archive Forums Links Staff Contact		Spring Pistol Buyer's Guide 3r^d Edition, 4/15/2002 Shane "Supergeek" Lin Super_geek@attbi.com Springer Retreat http://springer.airsoftretreat.com The spring pistol is the simplest of all airsoft weaponry, requiring a manual cycling of the mechanism before each shot. The spring pistol functions by the slide carrying the piston, holding a spring against the frame of the pistol, to a catch, which holds it in that compressed position. On the way back to the original position, the slide also pushes a BB from the top of the magazine through an incline and into an O-ring, which holds the BB in place in the barrel. Upon pulling the trigger, the catch that holds the piston is released, sending it forth, against the piston shroud and forcing air from the shroud into a hole leading into the barrel. The resulting sudden increase in air pressure between the BB and the piston causes the BB to accelerate down the barrel of the gun. Some pistols are equipped with the Hop-Up system, which puts a backwards spin onto the BB as it sails through the air. This motion causes the air at the lower end of the BB to have a lower pressure than the air traveling at the upper end of the BB, and thus through the Bernoulli principle, generates lift. Guns with the Hop-Up system will have a much higher effective range as the forces of drag and gravity will affect the BB to drop in angle much later, thus providing a much straighter shot. Many of these spring pistols (including many High Grade Hop-Up Mauri pistols and their subsequent UHC copies) can be field striped. This process involves removing the slide from the grip and frame of the pistol, so that the pistol and barrel can be removed and cleaned or lubricated. Spring pistols that have the Hop-Up system will have what is known as fixed Hop-Up, in which the Hop-Up is pre-calibrated for a certain weight BB. Most pistols have this calibrated for .12g BBs, with Mauri HG Hop-Up pistols for .25g and newer KWC spring pistols for .2g and .25g. However, any type of 6mm BB, regardless of weight can all used, to varying degrees of success, in all types of spring pistols. In addition to the large amount of automatic pistol replicas, there are also small number of revolver replicas, which work by the spring in the grip being compressed by a hammer. Upon trigger pull, the spring is released and air is forced through a tube into one of the chambers, where it forces the BB into the barrel. To understand the different aspects that make up a "good" spring pistol, first you must understand the factors that determine its effectiveness. These are the muzzle velocity (measured in FPS), the presence or absence of the Hop-Up system, and the quality of the materials and design for the internals and barrel (determined by manufacturer). Most of these can be determined by simply looking at different manufacturers, since the guns of the same company are pretty much on level with each other. Thus, a look at the major manufacturers of spring pistols follows: Tokyo Marui (TM): This most well known manufacturer of AEGs offers a wide selection of spring pistols. These can be classified into three groups, literally “the Good, the Bad, and the Ugly.” The “ugly pistols are the oldest TM designs, with the BBs in a stick which is inserted into the base of the grip. These guns thus have no magazine, limited functionality, and no Hop-Up. The "bad" Mauri pistols are the older "High-Grade non-Hop-Up" models. Aside from the obvious fact that these guns do not possess the hop-up system, many of them have internal and external technical problems that cause them to wear down and break easily. On the other side of the spectrum, the newer "High-grade hop-up" Mauri pistols are considered by many as the best on the market as well as the industry standard. These pistols have a fixed hop-up system calibrated for .25g BBs, offering more range than those calibrated for .12g BBs. The quality of the plastic used to make Mauri guns is noticeably better than those of Mauri's Hong Kong (HK) counterparts and TM guns have the reputation of being reliable and long lasting as well as effective. Unless I am mistaken, all of the better TM pistols include trademarks, which are legally covered by putty or tape. All TM guns are considered Light Weight (LW) as they weigh around 300-350 grams, about a quarter of the actual real steel version. In short, these are the best guns to get if you can get your hands on them, which may be a problem. There are very few US retailers online that carry TM springers, so online auction sites like Ebay may turn out to be your best bet. The other alternative is to purchase them from Asian-based online retailers like RedWolf Airsoft, Wargamer's Club, and DEN Trinity to name a few. The problem with this is that shipping across the vast expanse of the pacific ocean is costly and at the fastest shipping rate (SpeedPost, which takes 5-7 business days), a TM springer will cost $15-$25 to ship and runs the risk of being seized by US Customs. The final problem is price: TM pistols are the most expensive in the industry, and while the $40-$50 price tag may pale relative to an upgrade AEG, it is still at least twice as much as a UHC copy. For extra magazines, it may be more desirable to buy UHC magazines for guns of the same model, since the UHC pistols, and hence the magazines, are copied from the TM design. Thus, the magazines will work when swapped around. Bottom line: excellent choice for serious airsoft players looking to play skirmishes frequently, but bad for the occasional weekend warrior just looking to shoot at targets in the back yard most of the time. Tokyo Marui's Web Site is at: http://www.tokyo-marui.co.jp/ *Specific model analysis:* H&K Mk.23 SOCOM : This is perhaps one of the best spring pistols on the market. Its large size is justified by its performance: it seems to hit farther than other HG HU TM pistols. It is also the first and as of now, only TM pistol to have a threaded barrel, able to mount the 16mm threaded accesories as the KSC GBB and real steel Mk.23s. However, like all previous HG HU pistols, most of the operating controls are molded-on, and of course features like the decocker are not functional. However, it is still a very impressive peice, extremely functional and quite pleasing to the eye. It is such a good blend of these qualities that many state-side retailers have began to sell these guns, for rather reasonable prices as well. For some very nice pictures, check out the gallery in the Articles section of the Springer Retreat, at http://springer.airsoftretreat.com. *Additional Note: The latest Tokyo Marui models released, the Mk.23 SOCOM and the new HG HU Colt M1911, seem to be better and more powerfully designed and were only released in High Grade models. This could signify a move towards higher quality designs. UHC: Unicorn Hobbies Company of Taiwan is an interesting company. Most of their spring pistol designs are copied off of Mauri designs and made with cheaper materials with less stringent quality control (leading to the chance of a newly purchased gun being a “lemon,” although I myself have not encountered one in the dozen UHC guns that my team has bought). All of their guns include the hop-up system, calibrated for .12g BBs, which are less stable in wind than .2g BBs. A few of their models are also available in Light Weight and Heavy Weight (HW) models. The difference is that HW pistols are typically weighted down and are made of better looking and more durable materials. These changes push the weight from 300-350 grams to around 600-650 grams, depending on the model. These feel much more realistic in your hands, and can aid targeting. Accuracy for both LW and HW UHC guns are similar. While reportedly of slightly worse accuracy (in fair conditions - wind makes a big difference on accuracy as TM guns typically use .2g or .25g BBs as opposed to UHC's .12g BBs) than TM guns, UHC pistols do still have good reputations in the areas of reliability and service life. Although calibrated for .12g BBs, the hop-up unit on UHC guns can be used, with some success, to fire .2g BBs. This is from the author's personally experience, so maybe I was just lucky with my Beretta. Typically, the material quality of LW guns suffers while HW guns like the Beretta have a very nice matte black slide resembling the texture of the real article. There are no trademarks on UHC guns, although usually they tend to make clever parody logos that resemble the real ones. The magazine designs of both TM and UHC are identically. In a way, this is bad, because each BB must be individually loaded into the magazine, not like other designs were you could simply pour them in with a squeeze bottle. One bad aspect of UHC magazines is that when loaded with a few BBs and when pressure is applied to the upper side of the top BB, the entire magazine load of BBs flies out. This does not occur in TM pistols, even though the magazine design is the same, allowing the use of UHC magazines in TM pistols of the same model (and vice versa). When buying a UHC pistol, it is likely that UHC BBs will also be offered. While they are typically deformed and almost unusable in AEGs and gas guns, they will work quite well with springers, due to low price of spring pistols and the inherent tolerance of bad BBs by spring pistols. UHC pistols, unlike Mauri, are widely abundant in the US. They are imported mainly by two distributors: Leapers and Viper USA, which in turn ships them wholesale to retailers. LW pistols may be acquired for a mere $17 at www.tapco.com and HW models can be found in almost every major online airsoft-specific retailer (www.airsoftatlanta.com to name one) for $25 or so. Extra magazines are also offered at relatively low prices ($5). Bottom line: while not as well made, effective, reliable, long-lasting, or good-looking as Mauri guns, you can get two or even three UHCs for the price of a TM, and those two or three will last longer than the one Mauri. Good for plinkers and those just getting into airsoft. UHC's web site is at: http://www.toygunuhc.com.tw/ Specific model analysis:* Beretta 92: This is perhaps one of the best low-priced spring pistols widely available in the US. It features an open ejection port, well-made sights, comparatively ergonomic grip, protruding barrel (useful for attaching suppressors), double action trigger pull, very easy and realistic field stripping, and a lanyard attachment. The HW version of this gun also includes a very nicely textured slide of matte black (unlike the shiny LW one). Finally, the slide lock (which acts as a safety on this gun, can be altered so that it is once more a slide lock. Glock 17: The G17 is not a good choice for several reasons, the least of which is that I am a Beretta aficionado and think that Glocks look like undeveloped USPs. First, the ejection port does not open. This leads to situations in which a BB is left stuck in the slide area without a means of removal. Which brings me to the next problem: they cannot be field stripped and forced disassembly is reported difficult. While they do have decent accuracy, a pretty cool working trigger safety, and a relatively smooth slide pull, the Glock really cannot measure up to the Beretta in terms of ease-of-use. USP: The USP is quite simply, woefully underpowered. On many examples of this gun, the length of the slide is a bit too long for the spring to be completely compressed, leading to very low FPS and thus range. This phenomenon occurs in sufficient frequency so that the applicable examples cannot be dismissed as a mere "lemons." Fortunately however, the FPS problem can reported be fixed by adding a spacer to the end of the spring. It also does have an open ejection port and a rather unsightly open space under the barrel through which you can see a weight. But, on the bright side, it can be rather easily field stripped. KWC - Kien Well Co. of Taiwan offers some very nice pistols indeed. The guns are generally divided into two camps. Of the first, the exterior materials are superior to those used by UHC and there is a relatively large abundance of metal parts. The guns are of good quality and durability. The catch is that those guns do not shoot as accurately and do not have the Hop-Up system, killing the range at about 35 ft. The thing that's really devious is that many of these KWC guns have the hop-up logo very prominently displayed on the box, but most of them do not have it in reality. From my experience, these also have a bad tendency to break in ways so that the gun is unfixable without disassembly of the gun (which is a bit tricky to figure out). Acquiring these is done through major airsoft sites (like AirsoftAtlanta) for about the same price as UHC guns. The second camp of KWC guns are almost exactly the opposite. They are made of cheaper materials, are not very durable, have almost no metal parts, and seem to be easily broken, yet have exordinary performance for their price, with the help of .2g hop-up. The models of the KWC 1911 line follows the first camp (although reportedly, some of the newer models really do have hop-up), and the KWC "K"99 follows the second camp. Bottom line: The first type are good collector's items, for display purposes, but a less-than-great field weapon, while the second type are hardly ones to show off, but do offer very, very good performance. KWC's web site is at: http://www.kwc.com.tw/ *Additional note:* Newer model KWC guns, such as the P99. do have Hop-Up actually and are rather nice, especially as the Hop-Up is tuned to .20g BBs. *Specific model analysis:* K99 (KWC’s non-trademarked name for the P99): This is one of the newer KWC guns and it is very nice! In fact, it could compete with the UHC Beretta HW. While KWC does regrettably leave its tradition of numerous metal parts (like in their 1911 series), this gun does have many nice features. Among these is the .2g calibrated Hop-Up, the exposed (but not open barrel) ejection port area, the slide lock, the quick-load magazine (which annoyingly drops the top BB after being ejected), and top-notch slide charging action. The Hop-Up unit is covered with a thin layer of oil though, so out of the box, it shoots like a wounded llama, but after 100 rounds, it starts shooting VERY well. Colt 1911 10mm Custom: One of the 1911 series of KWC guns, this is a pretty old design. It has plenty of metal parts, a working grip safety, pretty high quality plastic body, slide lock, and a quick-fill magazine design, but lacks Hop-Up. But generally, this is a very decent collector’s gun. Desert Eagle .50AE: The melding of the two worlds, taking the best from either. This has been called by many as the best spring pistols ever made, and for good reason too: it's built like a GBB, with metal operating controls and a sturdy frame. It's quite good looking, with a full half-inch barrel diameter that tapers off into the 6mm inner barrel, unlike the Marui and UHC versions. Finally, and most importantly, it's got adjustable hop-up, that almost inconcievable luxury, unheard of in the world of springer airsoft. This allows it very good range with an assortment of BBs. This is certainly quite the formidable gun. HFC - Ho Feng Co. of Taiwan makes airsoft replicas of many of the more popular guns. Generally, they offer higher FPS than UHC pistols, but most models do not have hop-up. The materials, balancing, and design are also superior in some ways to UHC and Mauri pistols. For example, the sights on the HFC USP include a useful, if not simple, white dot for easy aiming. The UHC USP does not have this. Also, HFC does make the only HW USP on the market, and an excellent one at that as well. HFC guns may be purchased through most airsoft-specific online stores, but extra magazines for them are rather rare. Prices are similar to those of UHC HW pistols. Bottom line: good quality, good design, good looks, but since most guns do not have hop-up, range suffer too much to bear. The range difference is going to make you wish you'd have gotten a UHC in the long run unless you very desperately want a really good looking heavy USP. Additional Note: Newer HFC models now sport .12g-calibrated hop-up, although the models that do tend to be very limited and usually not widely available in the US. Inquire about it to a retailer before purchasing. *Specific model analysis:* USP/P8: This is pretty much the best USP made in terms of functionality, design, and weight. It is heavy weight, has an open ejection port, quick-fill magazine design, numerous metal parts, slide lock, very realistic safety, ambidextrous magazine eject lever, and nice color and textures. BUT, it doesn’t have Hop-Up, which pretty much limits effective range to about 30,40 feet. Finally, this gun is a bit badly-designed. The piston is connected to the slide at one point, which places enormous pressure on one thin section of the slide, right behind the ejection port. So, after a length of time of constant use, this part breaks, disabling the gun. Daisy - The famous American BB gun maker has gone back into the ring with their "Airstrike" pistol which, although reportedly really made by HFC, are at least readily available to the public through sports retailers and Walmart. while this obviously has the potential to cause harm to Airsoft's acceptance by the masses, it does provide the opportinity for the sport to grow. The "airstrike" pistol istelf is not much of a gun. It is based on a nickel-plated Beretta M92. The finish itself is not bad, but the large amounts of texts and warnings engraved on the slide itself is quite ugly. While there are plenty of metal parts for the operating controls, there is no hop-up, and accuracy and range are miserable. Overall, even with the avaialbility of this gun, it cannot be easily recommended. Y&P - Generally regarded as a low quality manufacturer, Y&P does make some models that are rare among other manufacturers, including the Walther P99 springer (better to buy the KWC version though). The general consensus on this manufacturer is that while the gun looks somewhat good, it shoots terribly and will easily break after repeated use. Bottom line: to be avoided, since you can just get a good UHC gun for about the same price. Y&P guns are imported in the United States primarily by Spring-Time International (or STTI). There are several Korean spring pistol manufacturers, but because of the general consensus being that the hierarchy of gun quality goes from Japan to Taiwan to Korea (and other countries), Korean regulations on gun FPS, and the relative scarcity of these pistols sold by US retailers, these cannot be seen as a serious consideration for pistol buyers, unless for display or collection purposes. Other than those, there is the French firm of 3PSA, which produces liscensed copies of the Marui guns for sale in Europe and the United States. Acknowledgments: Thanks particularly to Inferno, who has provided many details about Tokyo Mauri and KWC 1911-series spring pistols through the airsoft forums as well as influence in gun modifications. Also, thanks to everyone that commented on my mistakes or offered me praise and criticism.